1000-C1 Ceramic Adhesive

Normal setting Cement based Ceramic Adhesive Mortar.

General Information

Technical Information

Documents

AREAS OF UTILIZATION

It is used on surfaces such as concrete, screed, plaster with low water absorption, and for bonding low-size ceramics to horizontal and vertical floors indoors.
Ceramic area on indoor floor ≤ 750 cm2
Ceramic area on interior wall ≤ 500 cm2

ADVANTAGES OF THE PRODUCT

• It is ready to use, and it can be adjusted to the desired consistency by simply mixing with water.

• It prevents loss of labor and time with its ease of application.

PREPARATION OF THE SURFACE

• The surface should be cleared of residues such as oil, dirt, paint that will prevent adhesion.

• The surface should be clean, dry, smooth and in good condition.

• Cracked and hollow areas on the surface should be repaired with YurtKim Repair Mortar least 24 hours in advance.

• The dusty surface behind the ceramic should be moistened and wiped clean.

• In applications above 30°C, the surface should be moistened.

• In very hot and windy weather, the surface should be saturated with water.

• On floors with high water absorption, YurtKim Priming Coating EK220 should be used before the application and the bonding process should be continued by waiting for it to dry.

• During the application, the ambient temperature should be between +5 °C and +35 °C.

APPLICATION

• 25 kg YurtKim Ceramic Adhesive is poured onto 5,5-6,5 liters of clean water and mixed with a low-speed mixer until no lumps remain. The prepared mortar is rested for 5 minutes to mature and is used again after mixing for 1-2 minutes.

• The mortar is applied to the entire surface in circular movements with a combed trowel, which is selected according to the size of the ceramic and the structure of the surface.

• For surfaces and ceramics with high water absorption, Ceramic Adhesive should be applied to the back of the coating material to achieve double-sided bonding.

• During the application, it should be ensured that YurtKim Ceramic Adhesive does not form crusting on the surface; if such crusting has occurred, that part should be combed again, and if there is excessive drying in the mortar, it should be scraped from the surface and reapplied.

• The coating material is placed on the surface by adjusting the joint gaps.

• By tapping lightly with a rubber-tipped mallet, the coating material is placed on the surface.

• Joint filling process should be initiated at least 24 hours after bonding.

TECHNICAL SPECIFICATIONS

• Class of Reaction to Fire: A1

• Initial Adhesive Strength: ≥ 0.5 N/mm2

• Adhesive Strength after thermal aging: ≥ 0.5 N/mm2

• Tensile Adhesive Strength after Immersion in Water: ≥ 0.5 N/mm2

• Adhesion Strength After Freeze-Thaw Cycle: ≥ 0.5 N/mm2

• Adhesion Strength After Open Time: ≥ 0.5 N/mm2

• Maturation Time: 5 min.

• Pot Life: 1 hour

• Open Time: 10 min.

• Time Required for Joint Application: Minimum 24 hours.

• Commissioning time: Minimum 24 hours.

• Average Consumption: 5 kg/m2 according to the surface condition

• Temperature Resistance between -15°C and +70°C

• Application Thickness 3-10 mm (For Single and Double Sided Application)

• The above data was obtained based on the results of laboratory tests, and values may vary due to differences in the construction site environment.

COLOR

Grey

SHELF LIFE

Shelf life is 12 months when stored in its unopened original package in a way that is not exposed to moisture, dry and direct sunlight, provided that it is placed in a maximum of 8 rows on top of each other.

PACKAGING

25 kg± 2% Kraft Bag (64 bags on a pallet, 1600 kg)

STANDARD NO

TS EN 12004-1/Nisan 2017

C: Cement based

1: Normal Hardened (Standard Performance)

TDS

Do you have questions about this product?